Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Active Vibration Control of Boring Bar Vibrations
Ansvarlig organisasjon
2004 (engelsk)Rapport (Annet vitenskapelig)
Abstract [en]

The boring operation is a cumbersome manufacturing process plagued by noise and vibration-related problems. A deep internal boring operation in a workpiece is a classic example of chatter-prone machining. The manufacturing industry today is facing tougher tolerances of product surfaces and a desire to process hard-to-cut materials; vibrations must thus be kept to a minimum. An increase in productivity is also interesting from a manufacturing point of view. Penetrating deep and narrow cavities require that the dimensions of the boring bar are long and slender. As a result, the boring bar is inclined to vibrate due to the limited dynamic stiffness. Vibration affects the surface finish, leads to severe noise in the workshop and may also reduce tool life. This report presents an active control solution based on a standard boring bar with an embedded piezo ceramic actuator; this is placed in the area of the peak modal strain energy of the boring bar bending mode to be controlled. An accelerometer is also included in the design; this is mounted as close as possible to the cutting tool. Embedding the electronic parts not only protects them from the harsh environment in a lathe but also enable the design to be used on a general lathe as long as the mounting arrangements are relatively similar. Three different algorithms have been tested in the control system. Since the excitation source of the original vibrations, i.e. the chip formation process cannot be observed directly, the algorithms must be constructed on the basis of a feedback approach. Experimental results from boring operations show that the vibration level can be reduced by 40 dB at the resonance frequency of a fundamental boring bar bending mode; several of its harmonics can also be reduced significantly.

sted, utgiver, år, opplag, sider
2004.
Serie
Blekinge Institute of Technology Research report, ISSN 1103-1581 ; 7
Emneord [en]
Active Vibraion Control, Boring Bar Vibrations, Filtered-x LMS
HSV kategori
Identifikatorer
URN: urn:nbn:se:bth-00251Lokal ID: oai:bth.se:forskinfo8CD58085270D5E42C1256EE4003CC880OAI: oai:DiVA.org:bth-00251DiVA, id: diva2:837747
Tilgjengelig fra: 2012-09-18 Laget: 2004-08-02 Sist oppdatert: 2015-06-30bibliografisk kontrollert

Open Access i DiVA

fulltekst(2072 kB)661 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 2072 kBChecksum SHA-512
83c1b9003807c6907b67f72a4870bec356945b1be92d79377ed3b42183ad6028823e8e0f56b502bc07914eef49e02ebf7dda1c9b0375eda9cd07c7bcfa4d5357
Type fulltextMimetype application/pdf

Personposter BETA

Håkansson, Lars

Søk i DiVA

Av forfatter/redaktør
Håkansson, Lars

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 661 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

urn-nbn

Altmetric

urn-nbn
Totalt: 985 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf