Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
INITIAL EXPERIMENTS WITH A FINITE ELEMENT MODEL OF AN ACTIVE BORING BAR
Visa övriga samt affilieringar
Ansvarig organisation
2007 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat) Published
Abstract [en]

One of the most troublesome sources of vibration in metal cutting is the vibration caused by internal turning operations. A boring bar is a tool holder which is used to machine deep precise cavities inside a workpiece material. In order to perform this internal turning the boring bar usually has a large length-to-diameter ratio, and thus the boring bar vibrations are easily excited by the material deformation process during metal cutting. The vibrations are related to the lower order fundamental bending modes of the boring bar. To overcome the vibration problem an active control technique can be used. In particular, by utilizing an active boring bar with an embedded piezoceramic actuator and a suitable controller, the primary boring bar vibrations originating from the material deformation process may be suppressed with secondary "anti-" vibrations. In order to produce an active boring bar several decisions should be done, i.e. the characteristics of the actuator, the position of the actuator in the boring bar, etc. This usually implies that several prototypes of an active boring bar should be produced and tested, thus the design of an active boring bar is a tedious and costly procedure. Therefore a mathematical model which would incorporate the piezo-electric effect in order to predict the dynamic properties and the response of the active boring bar are of great importance. This paper addresses the development of a "3-D" finite element model of the system "boring bar-actuator-clamping house". The spatial dynamic properties of the active boring bar, i.e. its natural frequencies and mode shapes, as well as the transfer function between the voltage applied to the actuator and acceleration of boring bar are calculated based on the "3-D" FE model and compared to experimentally obtained estimates.

Ort, förlag, år, upplaga, sidor
Cairns, Australia, 2007.
Nyckelord [en]
active boring bar, actuator, finite element model
Nationell ämneskategori
Signalbehandling Teknisk mekanik
Identifikatorer
URN: urn:nbn:se:bth-9037Lokalt ID: oai:bth.se:forskinfo79F438C146C404C1C12573370025AE80OAI: oai:DiVA.org:bth-9037DiVA, id: diva2:836813
Konferens
ICSV 14 - The Fourteenth International Congress on Sound and Vibration
Tillgänglig från: 2012-09-18 Skapad: 2007-08-14 Senast uppdaterad: 2015-06-30Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Personposter BETA

Håkansson, LarsClaesson, Ingvar

Sök vidare i DiVA

Av författaren/redaktören
Håkansson, LarsClaesson, Ingvar
SignalbehandlingTeknisk mekanik

Sök vidare utanför DiVA

GoogleGoogle Scholar

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 90 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf