Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Active Control Machine Tool Chatter Embedded Piezo Ceramic Actuators in Tool Holder Shank
Ansvarig organisation
1999 (Engelska)Konferensbidrag, Publicerat paper (Refereegranskat) Published
Abstract [en]

In the turning operation chatter or vibration is a frequent problem, which affects the result of the machining, and, in particular, the surface finish. Tool life is also influenced by vibration. Severe acoustic noise in the working environment frequently occurs as a result of dynamic motion between the cutting tool and the workpiece. These problems can be reduced by active control of machine-tool vibration. Adaptive feedback control based on the filtered-x LMS-algorithm, enables a reduction of the vibration by up to 40 dB at 1.5 kHz and by approximately 40 dB at 3 kHz. The active control performed a broadband attenuation of the sound pressure level by up to 35 dB . A significant improvement of the workpiece surface was also observed. In the active control of tool vibration a tool holder construction based on integrated high magnetostrictive actuators was used. However, both the physical features and properties of an active tool holder construction based on high magnetostrictive actuators and the fact that this type of actuators generally have a non-linear behaviour highly reduce its applicability to the general lathe and turning operation. Therefor, a new generation embedded active tool holder shanks based on piezo ceramic actuators have been developed. Based on spectrum estimates, both coherence spectrum and frequency response function estimates has been calculated for both the old tool holder construction and the new generation active tool holder shank. From the results it follows that the phase delay is smaller and the linearity of the new generation active tool holder shank are superior compared to the old technology. It is also obvious that physical features and properties of new generation embedded active tool holder shanks based on piezo ceramic actuators fits the general lathe application.

Ort, förlag, år, upplaga, sidor
Las Vegas, 1999.
Nationell ämneskategori
Signalbehandling
Identifikatorer
URN: urn:nbn:se:bth-9992Lokalt ID: oai:bth.se:forskinfo598F3DCB4673FEB5C1256C6B00301AC4OAI: oai:DiVA.org:bth-9992DiVA, id: diva2:837999
Konferens
ASME 17th Biennial Conference on Mechanical Vibration and Noise
Tillgänglig från: 2012-09-18 Skapad: 2002-11-08 Senast uppdaterad: 2015-06-30Bibliografiskt granskad

Open Access i DiVA

fulltext(682 kB)87 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 682 kBChecksumma SHA-512
06f6fa0129f6dda21907660fa70ac7ce49a14d74456ddb3613176aaa75941fd6b5f39a5bb66bba085507b9820fe9018ab70313ab5e2cfff9a828f23b1c4e096d
Typ fulltextMimetyp application/pdf

Personposter BETA

Håkansson, LarsClaesson, Ingvar

Sök vidare i DiVA

Av författaren/redaktören
Håkansson, LarsClaesson, Ingvar
Signalbehandling

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 87 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 168 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf